Delta Homecraft Shaper The Vintage Delta Homecraft Shaper No. 34-500 8 inch Table Saw Jointer Combination machine offered a compact table saw jointer unit on one stand that used a single motor.
#VINTAGE DELTA UNISAW SERIES#
Overall dimensions with Wings and Guide Bars - 30 1/4" x 45 3/8"Ĭustom Search All Other Old Woodworking Tools Articles Delta Homecraft Tools Delta produced a series of woodworking machines for the homeowner called the Delta Homecraft Power Tools Delta Homecraft Jointer Delta homecraft jointer Delta Table Saw Jointer Combination Unit The Delta No. Miter Gage groove in table - 3/8" x 3/'4"
Perfect Safety - completely guarded motor switch can be locked.Point of Use controls and locks for convenient, safe operation.Big, Perfectly True Table Surface, 27" x 36".Patented, precision Auto-Set Miter Gage.Big Capacity - cuts to center of 50" panel and rips 3 1/8" stock.Perfected Raising, Lowering and Tilting Mechanism.Highly efficient 30 belt "Texrope" drive.True-running Arbor of sold forged allow steel.The design and construction features on the 1949 Unisaw featured the following: 1171 spacing collars and an extra saw blade, 1/4" or 3/8" tenons can be cut in a single pass.
#VINTAGE DELTA UNISAW FULL#
The tenoner will take stock up to 2 3/4" thick, any width within the capacity of the saw, and will cut tenons to full capacity of saw. Work is fed to the saw with one hand - far removed from the revolving blade. Tenoner makes all cuts safe, square, and parallel. 863 Extra Clamp Screw and Block for Clamp Attach. 865 Clamp Attachment for Miter Gage with Clamp Bar, two Sliding Clamp Screws and Front and Rear Posts. It can be adjusted to compensate for wear or loosening the head by merely loosening or tightening a tapered pivot screw. It can be set at any angle up to 60 degrees to the right or left, and it has adjustable stops for instantaneous settings at zero and 45 degrees to the right or left. The miter gage has a 7 inch face and a 3/8 x 3/4 x 18 inch bar which fits the table slot of circular saws and other machines. 1471 Super-Safe splitter-mounted guard was anchored directly to the arbor bracket so that when the saw is tilted the guard follows the saw blade - thus complete protection was always assured no mater what angle the saw was set. The LTA part number prefix was designated by Delta for all parts having to do with the Unisaw. Note the "LTA-402" designation on the underneath side of the extension wing castings. These 8" wide by 27" extensions madet the table a full 36" wide when bolted to each side. It also provided weight and an additional safety factor for the machine.Ĭast iron extension wings were available that bolt on to the sides of the Unisaw table top. 1454 Motor Cover Sometimes known as the Goose Egg cover because of its shape, the heavy cast iron motor cover enclosed the opening in which the motor swung. 34-405 - 10" Tilting Arbor Unisaw for 60 cycle service with side Extension Wings, Micro-Set Rip Fence, 10" Combination Blade, Auto-Set Miter Gage, Front Graduated Guide Bar, Motor Pulley, 3-V-Belts and Super-Safe Guard. The shaft was carried in two sealed-for-life ball bearings mounted in diamond bored bearing seats. The saw arbor bracket was a very heavy casting, with accurately machined teeth to fit the raising and lowering worm gear, and with accurate adjustable stops to limit up and down travel.
It also featured a micro adjust knob for fine movements. The front guide bar was graduated for quick setting of the fence. The standard guide bars allowed the fence to be moved 25" to the right of the saw blade and 15" to the left of the blade. The rip fence bar extended over the rear edge of the table and the fence locked both front and rear, the rear lock being operated from the front of the fence. The carriage swung on trunions that were large, heavy, and strong with working surfaces completely machined. Dado heads, molding cutters and many other attachments could be used to add to the versatility of the Unisaw. The blade was raised and lowered by another hand wheel at the front of the saw cabinet. The saw blade tilted 45 degrees to the right, operated by a large convenient hand wheel. With the standard rails and rip fence, it cut to the center of a 50" panel and ripped stock up to 3 1/8" thick. The saw table was 20 x 27 inches with optional cast iron extension wings that made it 36" wide by 27" deep. In 1949, the Delta-Milwaukee 10" Tilting Arbor Circular Saw was a completely self-contained motor and driving mechanism in a strong steel cabinet type base. Share your Unisaw Pictures with other visitors to this site. The Delta Unisaw has been one of the mainstays in home and industrial wood shops for over 60 years. Delta Unisaw - 10" Tilting Arbor Circular Saw (1949)Īccuracy - Long Life - Convenience with a Delta 10" Unisaw!
0 kommentar(er)
